Maytag Atlantis Washer Manual Remove Agitator Bell

Related Articles

May 06, 2018  To remove the agitator, you need to remove the top cap of the agitator. The cap is the portion above the cork screw vanes on the sides of the agitator. Pull hard on the cap and lift it off. That will expose a bolt going down the center of the agitator. Remove this bolt down the center and the entire agitator will lift up and off.

• 1 Troubleshoot an Admiral AAV8000AWW Washing Machine
• 2 Tips for Troubleshooting GE Washers
• 3 Troubleshoot Maytag Performa PAV2300 Washing Machines
• 4 Causes and Repair for a Whirlpool Washing Machine That Won't Spin or Rinse

Cara download file coursehero gratis. With regular care and maintenance, a Maytag Atlantis washing machine should perform well for years. Some problems require the attention of a professional, but many are simple enough to fix yourself, saving you a service call. Begin your troubleshooting by checking the outlet to make sure the machine is plugged in and to verify that the circuit hasn't tripped or a fuse hasn't blown. If that doesn't solve the problem, move on to the machine itself.

If Your Machine Won't Fill

A washing machine not filling is often the result of a water flow problem. Both faucets should be turned on fully. Check the inlet hoses that attach to the back of the machine and make sure they don't have kinks. The hoses must be placed at an elevation that is at least level with the top of the tub -- about 36 inches from the ground for the Maytag Atlantis. Another possibility is a blocked filter screen, which you can check by disconnecting the hoses and inspecting them internally.

If Your Machine Won't Agitate

When your washing machine fills with water but won't agitate, an improperly closed lid is the most common culprit. The Maytag Atlantis will not agitate unless the lid is completely closed, so check that the lid is tightly shut. New hindi movies download 2019. Once you're sure the lid is closed, turn the dial to the desired cycle and pull the knob outward to begin. Pauses throughout the cycle are normal. The Maytag Atlantis is equipped with a lid switch failure detector, and if this device malfunctions, it will stop the machine from functioning for your safety. Contact a professional for assistance with a malfunctioning lid switch failure detector.

If Your Machine Won't Spin or Drain

An improperly closed lid or malfunctioning lid switch failure detector can also be responsible for a washing machine that won't spin. Check the lid to make sure it is closed all the way, and then restart the cycle from the desired point. If the water does not drain from your washing machine, check the drain hoses for kinks and blockages. If the hoses are blocked, call for assistance. Water may not drain completely if the height of the drain is greater than 8 feet, and your clothes may come out wetter than normal if the load is unbalanced or if the spin setting is too slow for the load.

If Your Machine Leaks

Check the inlet hoses if your machine leaks water. The hoses should be tightly connected to both the water faucet and water valve. The drain hose may also leak, so ensure that the drain hose is properly inserted and connected to the drain facility. Leaks can also be caused by extended soaking and overloading, so avoid soaking clothes for longer than 30 minutes, and don't overload the washer. The maximum capacity of the Maytag Atlantis is 3.2 cubic feet. If your Maytag Atlantis overflows with soapy water, too much detergent is the likeliest cause.

About the Author

Richard Corrigan has been a full-time professional writer since 2010. His areas of expertise include travel, sports and recreation, gardening, landscaping and the outdoors. He earned a Bachelor of Arts in English from SUNY Geneseo in 2009.

Photo Credits

• Tim Boyle/Getty Images News/Getty Images

FYI Maytag Atlantis washer owners re: spin cycle problems. I wasted a lot of time trying to find out what was wrong with my washing machine with phone calls, internet searches and service calls. I was getting debris in the machine and soap on the clothes which were coming out wet from the machine which was smelly and moldy. The belt underneath was slipping and the repair man who came out and replaced the belt didn’t know what else to do. Frustrated with the lack of quality service from Maytag, I took it upon myself to open the machine (which is a fairly simple task), I found this site with directions http://www.applianceaid.com/atlantis.html .
Lo and behold the electric motor is mounted on a crappy sliding assembly which moves left or right depending on which cycle is running, only the flimsy track and tiny nylon bushing was full of crud preventing the motor sliding all the way and tightening the tension on the belt for the spin cycle. I then cleaned out the track and put in a healthy amount of lubricating oil in it, slid the motor back and forth manually for a bit and reassembled the housing. It has been 2 years or more since then and I have no more problems with the running of the machine, the smell has gone away with a little help from some bleach plus leaving the top up when not in use and there is no more detergent residue on the clothes.
It amazes me that nobody has found this easy fix before. I guess the old adage is true that if you want something done right, you have to do it yourself.
Sears Canada, Halifax, NS

• Maytag's response · Jun 05, 2017

  Mark, We regret to hear about your frustrations with your Washer. Unfortunately we are unable to offer assistance to those residing outside of the United States. Please visit http://www.maytag.ca/en_CA/ for assistance in your region.